Scroll Up


Detection (Sensors) > Photoelectric Sensors >WORLD-BEAM QS30 Series WORLD-BEAM QS30 Standard
WORLD-BEAM QS30 Standard

Marka: Banner Engineering

Product Labels: WORLD-BEAM QS30 Standard, Banner Engineering

WORLD-BEAM QS30 Standard

  • Product Specifications
  • Product Documents
  • Similar Products
Product Specifications

Overview

  • 30 mm threaded barrel or right-angle mounting options 
  • 10 to 30V dc supply voltage with bipolar NPN/PNP outputs 
  • Available in opposed, polarized and non-polarized retroreflective and diffuse sensing modes
  • Ranges up to 60 m
  • Selectable light- or dark-operate, depending on hookup 
  • IP67 and NEMA 6 rating for use in harsh environments
  • Bright LED operating status indicators visible from 360°

Product Specifications

Supply Voltage and Current 10 to 30V dc (10% max. ripple) @ 45 mA (exclusive of load)
Range Opposed:60 m
Non-polarized Retroreflective:12 m, range is specified using one model BRT-84 retroreflector
Polarized Retroreflective:8 m, range is specified using one model BRT-84 retroreflector
Diffuse:1.0 m
Supply Protection Circuitry Protected against reverse polarity, over voltage and transient voltages
Output Configuration Bipolar:One NPN (current sinking) and one PNP (current sourcing); light operate (LO) or dark operate (DO) selectable or configurable, depending on model
Output Rating 100 mA max. each output @ 25° C OFF-state leakage:

NPN:less than 200 µA @ 30V dc

PNP:less than 10 µA

ON-state saturation voltage:

NPN:less than 1.6V @ 100 mA

PNP:less than 2.0V @ 100 mA
Output Protection Circuitry Protected against output short-circuit, continuous overload, transient over-voltages and false pulse on power-up
Output Response Time Opposed:5 milliseconds ON/OFF
All others:2 milliseconds ON/OFF
Delay at Power-up 100 milliseconds; outputs do not conduct during this time.
Repeatability Opposed:not applicable
All others:500 microseconds
Adjustments Opposed, Polarized Retroreflective and Non-polarized Retroreflective:Selectable light/dark operate is achieved using the gray wire

Light Operate:Low (0 to 3V)*

Dark Operate:High (open or 5 to 30V)*

Diffuse:

Light Operate:High (open or 5 to 30V)*

Dark Operate:Low (0 to 3V)*

Diffuse, Polarized Retroreflective and Non-polarized Retroreflective:Single-turn sensitivity(Gain) adjustment potentiometer
*Note:Input impedance 10 k ohms
Indicators Large, oval LED indicator on back (Except Emitter):

Yellow ON steady:output conducting

2 LED indicators on top:Green and Yellow

Green ON steady:power ON

Green flashing:output overloaded (except receivers)

Yellow ON steady:light sensed

Yellow flashing:marginal excess gain (1.0-1.5x excess gain)
Construction PC/ABS housing with acrylic lens cover
Environmental Rating IP67; NEMA 6
Connections 5-conductor 2 m or 9 m attached PVC cable, or 4-pin Euro-style quick-disconnect fitting. QD cables are ordered separately. 
Operating Conditions Temperature:-20 to +70° C
Relative humidity:90% @ 50° C (non-condensing)
Vibration and Mechanical Shock All models meet Mil. Std. 202F requirements. Method 201A (Vibration; frequency 10 to 60 Hz max., double amplitude 0.06-inch acceleration 10G). Also meets IEC 947-5-2 requirements: 30G, 11 milliseconds duration, half-sine wave.

 

Product Documents
WORLD-BEAM QS30 Standard Series, dc models22.12.2014 - 1 MbİngilizceCheck Out
Similar Products

D10 Discrete Output

D10 Expert - Small Object Counter