Supply Voltage and Current | 10 to 30V dc (10% max. ripple) Laser Emitters:less than 35 mA (exclusive of load) All others:less than 15 mA (exclusive of load) |
---|---|
Range | Laser Emitter:15 m (4500 X excess gain) Laser Polarized Retroreflective:10 m, range is specified using one model BRT-51X51BM or BRT-TVHG-2X2 retroreflector Laser Diffuse:300 mm Class 1 Laser Adjustable-field:1 mm to cutoff point (adj. between 30-150 mm) Class 2 Laser Adjustable-field:20 mm to cutoff point (adj. between 50-250 mm) |
Laser Characteristics | Wavelength:
Class 2 Laser Adjustable-field:658 nm visible Class 2 laser All others:650 nm visible red Class 1 laser Pulse width:Laser Emitters:5 microseconds All others:7 microseconds Rep. rate:Laser Emitters:27 microseconds All others:130 microseconds Pulse output power:Laser Emitters:less than 1.9 mW All others:0.065 mW |
Supply Protection Circuitry | Protected against reverse polarity and transient voltages |
Laser Control | Enable beam by applying 0V dc to white wire; apply +10 to 30V dc to white wire to inhibit (extinguish) beam |
Output Configuration | Solid-state complementary (SPDT):NPN (current sinking) or PNP (current sourcing), depending on model |
Output Rating | 100 mA max. each @ 25° C OFF-state leakage current:
NPN:less than 200 µA @ 30V dc PNP:less than 10 µA @ 30V dc ON-state saturation voltage:NPN:less than 1.6V @ 100 mA PNP:less than 2.0V @ 100 mA |
Output Protection Circuitry | Protected against false pulse on power-up and continuous overload or short circuit of outputs |
Output Response Time | 700 microseconds ON/OFF (except Laser Emitters) |
Delay at Power-up | Laser Emitters:1.5 seconds All others:200 milliseconds; outputs do not conduct during this time. |
Repeatability | 130 microseconds (except Laser Emitters) |
Sensing Hysteresis | Laser Retroreflective:12% of range typical Laser Diffuse:15% of range typical Class 1 Laser Adjustable-field:1% of range typical @ 30 mm cutoff; 2% of range typical @ 75 mm cutoff; 5% of range typical at 150 mm cutoff Class 2 Laser Adjustable-field:1% of range typical @ 50 mm cutoff; 2% of range typical @ 150 mm cutoff; 5% of range typical at 250 mm cutoff |
Adjustments | Laser Retroreflective and Laser Diffuse:Single-turn sensitivity (Gain) adjustment potentiometer Class 1 Laser Adjustable-field:Five-turn adjustment screw sets cutoff distance between 30 and 150 mm, clutched at both ends of travel Class 2 Laser Adjustable-field:Five-turn adjustment screw sets cutoff distance between 50 and 250 mm, clutched at both ends of travel |
Construction | ABS housing with acrylic lens cover. 2.5 mm (laser adjustable-field) and 3 mm mounting hardware is included with each sensor. |
Indicators | Laser Emitters, 1 LED indicator:
Green ON steady:power applied All others, 2 LED Indicators:Green ON steady:power ON Green flashing:output overload Yellow† ON steady:light sensed Yellow† flashing:marginal excess gain (1.0-1.5x excess gain) in light condition †Note::Prior to date code 0223, the output indicator was red instead of yellow. |
Environmental Rating | IEC IP67; NEMA 6 |
Connections | 2 m or 9 m 4-wire attached PVC cable, or 150 mm pigtail with 4-pin Pico-style QD (Q), or 150 mm pigtail with 4-pin Euro-style QD (Q5), or 4-pin integral Pico-style QD (Q7), or 4-pin integral Euro-style QD (Q8), depending on model. QD cable are ordered separately. |
Operating Conditions | Temperature:-10 to +50° C Relative humidity:90% @ 50° C (non-condensing) |
Laser Classification | Laser products comply with EN60825-1; 2001 and 21 CFR 1040:10, except deviations persuant to Laser Notice 50, dated 7-26-01. |
Address | : | Oruçreis Mah. Tekstilkent Cd. Tekstilkent Ticaret Merkezi A8 Blok No:17/18/19 Esenler / Istanbul / Turkey |
Telephone | : | +90 212 210 76 46 |
Fax | : | +90 212 220 50 45 |
: | info@dacel.com.tr |