Lighting Automation > KNX (EIB) Input Output Equipments
Output Devices
5WG1502-1AB02 Siemens KNX combi switching actuator 8 x AC 230 V, 16 A 8 x binary input N 502-02

Marka:

Product Tags:


Product Specifications

Type

5WG1502-1AB02(N 502/02)

Description

Combi switching actuator‚ 8 x AC 230 V‚ 16 A‚ 8 x binary inputs

Combi switching actuator‚ 8 x AC 230 V‚ 16 A‚ 8 x binary inputs

  • 8 inputs AC/DC 12...230 V
  • 8 relay contact outputs
  • Rated contact voltage AC 230 V
  • Rated contact operating current 16 A‚ p.f. = 1
  • Electronics power supply via an integrated power supply unit for AC 230 V
  • Device functional even without bus connection or if bus voltage absent or bus communication interrupted or not yet activated
  • Green LED to indicate operational readiness
  • Push button to switch between bus and direct mode
  • Yellow LED to indicate direct mode activated
  • Push button for each output to switch the output in direct mode via a toggling function by a short actuation and for changing the output mode between remote control relay and time switch relay by holding down the push button for some seconds
  • 1 red LED per output to indicate the switching state
  • 1 red LED per input to indicate the current signal state
  • Device preset at the factory for direct switching of an output through a toggling function via the input of the same name
  • Selectable function for each input when using the Engineering Tool Software (ETS):
  • Switching status / binary value transmission
  • Switching‚ short / long operation
  • Single button dimming‚ single button sun protection control‚ 1-button group control (sequence control)
  • 1-bit scene control
  • 8-bit scene control‚ 8-bit value‚ edge-triggered‚ 8-bit value‚ short / long operation
  • 16-bit floating point value‚ edge-triggered‚ 16-bit value‚ short / long operation‚ 16-bit value‚ edge-triggered‚ 16-bit floating point value‚ short / long operation
  • Selectable function for each pair of inputs: 2-button dimming with stop telegram‚ 2-pushbutton shutter/ blind control
  • Selectable blocking / releasing of each input via a corresponding blocking object
  • Sending of the input objects after a change of status
  • Selectable logic operation (AND/OR) for one input with a further communication object and with variable start value of the logic operation at bus voltage recovery
  • Setting by means of the ETS‚ whether all outputs are to be configured identically or individually
  • Selectable mode for each output (normal mode‚ time switch mode)
  • Optional addition of a night mode object for each output for time-limited switching On of the output (and hence the illumination) at night
  • Variable On and Off delay times for each output
  • Variable On period in night mode or in time switch mode
  • Selectable warning signal prior to imminent switching-off by means of three-times short off and on switching (flashing) in night mode or in time switch mode
  • Status object for reporting direct mode
  • Optional status object per output for status reporting
  • Sending of status objects on request and/or automatically after a change
  • Integrated 8-bit scene control and linking of each output with up to 8 scenes
  • Selectable switching state for each output at mains or bus power failure as well as after bus or mains voltage recovery
  • Integrated bus coupling units with only half a standard bus load
  • Bus connection via bus terminal or contact system to data rail
  • Modular installation devices for mounting on TH35 EN 60715 mounting rail

 

     Dimension width (1 MW = 18 mm)                      8 MW

Product Documents
5WG1502-1AB02 combi switching actuator 8 x AC 230 V, 16 A 8 x binary input N 502-0230.09.2015 - 1 MbİngilizceDownload
Similar products